LG Washer-Dryer Combos & WashTower Repair

Washer-Dryer Combos & WashTower Repair, Done Right the First Time

This category covers two different LG products that both put more laundry function into one footprint: the WashCombo, a single ventless drum that washes and dries the same load without moving it, and WashTower, a washer and dryer stacked in one cabinet under one shared control panel.

Book Washer-Dryer Combos & WashTower Repair

Same-day & next-day appointments · No hidden fees · Technicians trained on these appliances

1Service Details
2Date & Time
3Contact Info

or call (844) 523-2969 now

WashCombo and WashTower solve the same space problem in different ways. WashCombo is a single ventless drum that washes and then dries the same load without transferring it anywhere, which means the heating, the heat-pump condenser and the drying air path all live inside the same cabinet as the wash components – a fault in drying sits physically close to the wash side, and getting to it means going past it. WashTower keeps a separate washer and dryer, each with its own drum and drive, but stacks them in one cabinet under one shared control panel that both halves report to.

Because both products are newer to LG’s US lineup than its standalone washers and dryers, we confirm the exact model before quoting – the parts, the fault-code set and even which half of a WashTower failed are not always obvious from the outside of the cabinet. On WashCombo units we pay particular attention to the drying-side components, since that is where LG’s own documentation places the dHE code and where most of the drying-only complaints we see turn out to sit.

We isolate the unit at the breaker and close the supply taps before any panel is opened, and on a WashTower we check the shared control and the connection between the two halves before treating a fault as belonging to one side alone.

Common Washer-Dryer Combos & WashTower Problems

01

WashCombo finishing the wash phase but leaving the load wet after drying

02

dHE shown on the display during the drying phase of a WashCombo cycle

03

WashTower washer or dryer half not responding to the shared control panel

04

Total cycle time stretching far past the time shown when the load started

05

One half of a WashTower reporting a fault while the other runs normally

06

Cd shown at the end of a drying cycle with the load already finished

Washer-Dryer Combos & WashTower Error Codes

Recognize a code on your display? Look it up before you unplug anything or attempt a repair.

See all Error Codes →

Popular LG Washer-Dryer Combos & WashTower Models

Why Trust Us With Your LG Washer-Dryer Combos & WashTower

  • Trained on LG washer-dryer combos & washtower control systems and diagnostics.
  • Genuine OEM parts stocked for the most common failures.
  • Upfront flat-rate pricing, approved by you before we start.
  • 30-day workmanship warranty on every repair. Parts may carry the manufacturer's warranty where applicable.
FAQ

Washer-Dryer Combos & WashTower Repair FAQ

LG documents dHE specifically for the drying phase of its ventless WashCombo units, where it points at the heat-pump drying circuit rather than at the wash side of the machine. Because the wash and dry functions share one drum and one set of plumbing on these machines, a dHE code narrows the fault to the drying components before a technician even arrives, which is useful given how much sits behind that single cabinet.

No. Cd is LG's cool-down notice, shown for a short period after the drying phase ends while the drum and the load lose heat before the door unlocks. It clears on its own and is not a fault code.

Electrically, closer to one. The washer and dryer halves share a single control panel and, on most models, pass fault information between the two sections, so a problem that looks like it belongs to the dryer half can sometimes trace back to the shared board instead. We check both halves and the connection between them before assuming a fault is isolated to the unit that is actually complaining.

If the wash phase completes normally and there is no water reaching the floor, running a wash-only program is usually possible on these machines while a drying-side repair is scheduled. Switch it off at the breaker and stop using it altogether if you see water outside the drum or smell anything overheating during any part of the cycle, and leave it off until it has been looked at.

Need a repair? We're ready to help. Call Now
Call Us Schedule